Lumenlab > pun15her

Solarex

Jun 23 2005, 11:49 PM

QUOTE (pun15her @ Jun 23 2005, 03:00 PM)

I do have 1 piece of tempered glass,the rear fresnel sits ontop of it,booth are in the rear frame.I was worried about warping the fres,but that hasn't happened,(yet!)

ok, no wonder i only see three stacks. i guess that proves your cooling method works well.

pun15her

Jun 24 2005, 11:34 AM

Just playing with ideas today,I was thinking of making a Samurai Lightgate/box.
I was thinking of something like this:

Any glaring problems that anyone can see???
I hope it makes sense!!

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

samuraijack

Jun 24 2005, 11:55 AM

QUOTE (pun15her @ Jun 24 2005, 11:34 AM)

Just playing with ideas today,I was thinking of making a Samurai Lightgate/box.
I was thinking of something like this:

Any glaring problems that anyone can see???
I hope it makes sense!!

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

Thats the beauty of the vertical design. It leaves more options open for design. I like it. I found a supplier of optically nuetral glass that you could use. No too expensive. The port you need it actually only 2.5 x 3 inches, depending on how close the bulb is to the port.

pun15her

Jun 24 2005, 12:11 PM

QUOTE (samuraijack @ Jun 24 2005, 11:55 AM)

QUOTE (pun15her @ Jun 24 2005, 11:34 AM)

Just playing with ideas today,I was thinking of making a Samurai Lightgate/box.
I was thinking of something like this:

Any glaring problems that anyone can see???
I hope it makes sense!!

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

Thats the beauty of the vertical design. It leaves more options open for design. I like it. I found a supplier of optically nuetral glass that you could use. No too expensive. The port you need it actually only 2.5 x 3 inches, depending on how close the bulb is to the port.

Thanks for the thumbs up,Samurai,That glass sounds good,I will see if I can find some in the UK.
I didnt realise the port could be quite that small! Wow.

smejworth

Jun 24 2005, 12:20 PM

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

Any glaring problems that anyone can see???

That looks like the go. Do you have enough room to center the globe with that orientation?

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

I must say I've thought about this while planning my projector, but I'm not sure about how tilting the triplet would effect the optics, I suspect you might be able to get away with a few degrees before losing brightness and image clarity.

I'd be very interested in your results if you end up try it.

samuraijack

Jun 24 2005, 12:34 PM

QUOTE (pun15her @ Jun 24 2005, 12:11 PM)

QUOTE (samuraijack @ Jun 24 2005, 11:55 AM)

QUOTE (pun15her @ Jun 24 2005, 11:34 AM)

Just playing with ideas today,I was thinking of making a Samurai Lightgate/box.
I was thinking of something like this:

Any glaring problems that anyone can see???
I hope it makes sense!!

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

Thats the beauty of the vertical design. It leaves more options open for design. I like it. I found a supplier of optically nuetral glass that you could use. No too expensive. The port you need it actually only 2.5 x 3 inches, depending on how close the bulb is to the port.

Thanks for the thumbs up,Samurai,That glass sounds good,I will see if I can find some in the UK.
I didnt realise the port could be quite that small! Wow.

When I was calculating the apeture for the Lightgate ( I did it all by pen, paper and ruler at true size...)I used the bulb set back from the apeture of the gate by 2.25 inches. Based on the spread of the theoretical "cone", I came up with that to provide coverage to a 15 inch lcd. Then I oversized it by a few square inches. Im working on the iris tonight I think. I had to take last night off..

pun15her

Jun 24 2005, 12:43 PM

QUOTE (smejworth @ Jun 24 2005, 12:20 PM)

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

Any glaring problems that anyone can see???

That looks like the go. Do you have enough room to center the globe with that orientation?

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

I must say I've thought about this while planning my projector, but I'm not sure about how tilting the triplet would effect the optics, I suspect you might be able to get away with a few degrees before losing brightness and image clarity.

I'd be very interested in your results if you end up try it.

I've been mulling this over for a while now,and I have come to the conclusion that,if you can pivot the triplet round the central point of the optics path,(eg:the centre of the mirror) and can also pivot the mirror through the same point,in theory you could swivel the triplet,and the mirror to correspond through a very large arc.
Please forgive the scribble:

In theory at least,this would give major movement,although the mirror would need to be adjusted along with the triplet.

Cheers P

(if I could find a way to gear the mirror to move at 50% of the movement of the triplet,the whole process could be motorised!!!

)

joecnc2006

Jun 24 2005, 02:21 PM

I like it, Punisher I would still like to layout your projector in Solid works and make a kit out of it if you are willing? (with the Pun15her Logo cut into the sides)

Same Material Used in my HassMan for the front curve.

Joe

samuraijack

Jun 24 2005, 02:37 PM

QUOTE (joe2000chevy @ Jun 24 2005, 02:21 PM)

I like it, Punisher I would still like to layout your projector in Solid works and make a kit out of it if you are willing? (with the Pun15her Logo cut into the sides)

Same Material Used in my HassMan for the front curve.

Joe

You could use his name, but the logo would be a copyright infringement...Marvel is militant about their copyright materials.

Sorry, dont mean to be a wet blanket...Its just that the copyright laws are moving towards being obscene and I dont want anyone to get in trouble.

Mountainbiker54

Jun 24 2005, 02:50 PM

hey punisher I was putting my top fresnel at a 10 degree angle, and my lens at a 10 degree angle, but I end up getting a trapizod on the screen, any idea why?

pun15her

Jun 24 2005, 02:54 PM

I think that would be awesome Joe,please do.
Any help I can give you,just let me know!!

My avatar is similar to the punisher logo,but maybe it is different enough to be OK???????
At the end of the day,though,I would be happy to have the design out there in any form.

samuraijack

Jun 24 2005, 03:13 PM

QUOTE (pun15her @ Jun 24 2005, 02:54 PM)

I think that would be awesome Joe,please do.
Any help I can give you,just let me know!!

My avatar is similar to the punisher logo,but maybe it is different enough to be OK???????
At the end of the day,though,I would be happy to have the design out there in any form.

This is an example of how Marvel works...

"The Emperor is not as forgiving as I am."

Since they forged bonds with the movie companies, they have pooled resources and become quite the force to be reckoned with.

SupraGuy

Jun 24 2005, 03:36 PM

Joe: Pun style projector cases... That would be awesome.

Pun: I like the pico idea. A 2:1 gearing for the projection lens vs mirror should be easy enough to make, though it would require some precision to make. The mechanism would be similar in concept to the one that allows a clock's hands to be driven at different speeds, though a simple 2:1 that only needs to voce a relatively small arc should be good.

MB54: I'll post a solution in your PLOG.

pun15her

Jun 24 2005, 04:06 PM

QUOTE (Mountainbiker54 @ Jun 24 2005, 02:50 PM)

hey punisher I was putting my top fresnel at a 10 degree angle, and my lens at a 10 degree angle, but I end up getting a trapizod on the screen, any idea why?

To be perfectly honest,I havn't quite been able to suss that one out yet!!
Raise the angle more and it will dissapear eventually!Also the angle of the mirror can accentuate the trapezoid shape,too,if you tilt the mirror,the shape lessens.
I am going to go half fresnel adjustment,and half by a slanted screen.That way I hope to keep reasonable focus across the screen too!!

QUOTE (samuraijack @ Jun 24 2005, 03:13 PM)

QUOTE (pun15her @ Jun 24 2005, 02:54 PM)

I think that would be awesome Joe,please do.
Any help I can give you,just let me know!!

My avatar is similar to the punisher logo,but maybe it is different enough to be OK???????
At the end of the day,though,I would be happy to have the design out there in any form.

This is an example of how Marvel works...

"The Emperor is not as forgiving as I am."

Since they forged bonds with the movie companies, they have pooled resources and become quite the force to be reckoned with.

Jeez,how anal!!!Oh well,it would have been nice.

samuraijack

Jun 24 2005, 04:21 PM

QUOTE (pun15her @ Jun 24 2005, 04:06 PM)

QUOTE (Mountainbiker54 @ Jun 24 2005, 02:50 PM)

hey punisher I was putting my top fresnel at a 10 degree angle, and my lens at a 10 degree angle, but I end up getting a trapizod on the screen, any idea why?

To be perfectly honest,I havn't quite been able to suss that one out yet!!
Raise the angle more and it will dissapear eventually!Also the angle of the mirror can accentuate the trapezoid shape,too,if you tilt the mirror,the shape lessens.
I am going to go half fresnel adjustment,and half by a slanted screen.That way I hope to keep reasonable focus across the screen too!!

QUOTE (samuraijack @ Jun 24 2005, 03:13 PM)

QUOTE (pun15her @ Jun 24 2005, 02:54 PM)

I think that would be awesome Joe,please do.
Any help I can give you,just let me know!!

My avatar is similar to the punisher logo,but maybe it is different enough to be OK???????
At the end of the day,though,I would be happy to have the design out there in any form.

This is an example of how Marvel works...

"The Emperor is not as forgiving as I am."

Since they forged bonds with the movie companies, they have pooled resources and become quite the force to be reckoned with.

Jeez,how anal!!!Oh well,it would have been nice.

Im sorry. I was going to say something earlier when it was mentioned, but I didnt want to seem like a party pooper. If the design is built and sold with nods from admins, then the LL group would probably assume some of the liability as well.

BUT! They could still sell it with your name and I really do think people should have a chance to get one. It is such a good looking design.

Like I said, Im sorry, but I had these visions of them making your life a living hell, maybe even freezing LL's assetts, and I hate seeing my friends get hurt, so I figured I had better speak up.

Come to think of it, my avatar is probably a CI too...

pun15her

Jun 24 2005, 08:07 PM

Last of the V8 Interceptors

samuraijack

Jun 24 2005, 11:56 PM

QUOTE (pun15her @ Jun 24 2005, 08:07 PM)

Last of the V8 Interceptors

Was that for me? Thanks Pun15her!

Someone mentioned Mad Max before and I quipped that line from the Mechanic. I liked that one, but I think I watched Road Warrior about 30 times...

"My dogs of War..."

Hope everyone has a good weekend.

pun15her

Jun 25 2005, 09:00 PM

QUOTE (samuraijack @ Jun 24 2005, 11:56 PM)

QUOTE (pun15her @ Jun 24 2005, 08:07 PM)

Last of the V8 Interceptors

Was that for me? Thanks Pun15her!

Someone mentioned Mad Max before and I quipped that line from the Mechanic. I liked that one, but I think I watched Road Warrior about 30 times...

"My dogs of War..."

Hope everyone has a good weekend.

You gotta love "fi-fi"

my4keys82

Jun 25 2005, 09:01 PM

Amazing looking projector Punisher, well done and thanks for your very informative plog.

Can I ask as to where you sourced the tube which the triplet sits in, I'm not having much luck finding anything the right size apart from cans of food which I'm not too keen on. Thanks.

pun15her

Jun 26 2005, 11:08 AM

QUOTE (my4keys82 @ Jun 25 2005, 09:01 PM)

Amazing looking projector Punisher, well done and thanks for your very informative plog.

Can I ask as to where you sourced the tube which the triplet sits in, I'm not having much luck finding anything the right size apart from cans of food which I'm not too keen on. Thanks.

Hi,my4keys82.

Thanks for the kind words,I accumulated loads of stuff when trying out focus solutions,the tubes I eventually used were from a big b&q.They were in the plumbing section.Just 2 short lengths of black plastic tubing (about 10cm).one runs inside the other.Took a bit of sanding to get them to run smoothly,though!!
Hope this helps!

SonicWonder2000

Jun 26 2005, 08:14 PM

QUOTE (smejworth @ Jun 24 2005, 12:20 PM)

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

Any glaring problems that anyone can see???

That looks like the go. Do you have enough room to center the globe with that orientation?

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

I must say I've thought about this while planning my projector, but I'm not sure about how tilting the triplet would effect the optics, I suspect you might be able to get away with a few degrees before losing brightness and image clarity.

I'd be very interested in your results if you end up try it.

I've got one on my pj, and the jury is still out on it's effectiveness. I haven't had a chance to play with it for long enough yet. One of the things that is making it hard is that I don't have a lock for my triplet slide yet, it is on rails. I'm finding it very difficult to play with the tilt without disrupting the slide mechanism.

Pun, I don't think that tilt alone will create a shift in the position of the projected image, or keystone correct.

pun15her

Jun 26 2005, 08:37 PM

QUOTE (SonicWonder2000 @ Jun 26 2005, 08:14 PM)

QUOTE (smejworth @ Jun 24 2005, 12:20 PM)

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

Any glaring problems that anyone can see???

That looks like the go. Do you have enough room to center the globe with that orientation?

QUOTE (pun15her @ Jun 24 2005, 09:34 PM)

I am also looking at a swiveling triplet assembly to raise and lower the projected image.

I must say I've thought about this while planning my projector, but I'm not sure about how tilting the triplet would effect the optics, I suspect you might be able to get away with a few degrees before losing brightness and image clarity.

I'd be very interested in your results if you end up try it.

I've got one on my pj, and the jury is still out on it's effectiveness. I haven't had a chance to play with it for long enough yet. One of the things that is making it hard is that I don't have a lock for my triplet slide yet, it is on rails. I'm finding it very difficult to play with the tilt without disrupting the slide mechanism.

This is what I was thinking about,(sorry for the scribble).The triplet would be on a bar,that would pivot about the centre point of the lightpath at the mirror,that way,the mirror could be used to redirect the lightpath to follow the movement of the triplet,all moving in the same plane!!!?????

Pun, I don't think that tilt alone will create a shift in the position of the projected image, or keystone correct.

jniehenk

Jun 27 2005, 07:03 AM

I've been mosying through this post and others for weeks now and am still lost on the picture quality of this design. What angle roughly is your top fresnal set at and does this correct your keystoning. also does your picture focus from top to bottom. I have an all thread frame built and am thinking of builing the super pivot for the mirror and triplet tomorrow. hard to tell but is your lcd facing the lamp or the triplet, think i messed up and designed my frames to accomodate the lcd fasing the the lamp and the boards sticking up.

Haas_man

Jun 27 2005, 11:09 AM

I was looking into a pivot on the mirror for my next box, whenever that happens. I have a simular design sketched up. The problem is that the mirror and obj lens need to move at different rates. If the mirror is tipped back 10 deg. , then the obj needs to be be raised by 20 degrees. I have sketched up a design that will compensate for the correction, but it's on paper not CAD. My design also corrects for the keystone angle too. I guess I'm not going to supprise anyone now!

edit: I see that your mirror and lens were not connected. I was trying to do it in one motion. tip the lens up and the mirror and f fres make the correction with simple levers.

joecnc2006

Jun 27 2005, 11:56 AM

QUOTE (jniehenk @ Jun 27 2005, 02:03 AM)

I've been mosying through this post and others for weeks now and am still lost on the picture quality of this design. What angle roughly is your top fresnal set at and does this correct your keystoning. also does your picture focus from top to bottom. I have an all thread frame built and am thinking of builing the super pivot for the mirror and triplet tomorrow. hard to tell but is your lcd facing the lamp or the triplet, think i messed up and designed my frames to accomodate the lcd fasing the the lamp and the boards sticking up.

Lcd faces the triplet, with boards facing down.

pun15her

Jun 27 2005, 02:25 PM

QUOTE (joe2000chevy @ Jun 27 2005, 11:56 AM)

QUOTE (jniehenk @ Jun 27 2005, 02:03 AM)

I've been mosying through this post and others for weeks now and am still lost on the picture quality of this design. What angle roughly is your top fresnal set at and does this correct your keystoning. also does your picture focus from top to bottom. I have an all thread frame built and am thinking of builing the super pivot for the mirror and triplet tomorrow. hard to tell but is your lcd facing the lamp or the triplet, think i messed up and designed my frames to accomodate the lcd fasing the the lamp and the boards sticking up.

Lcd faces the triplet, with boards facing down.

Cheers Joe,yup that is correct,lcd aces triplet.I have the board facing up!!The fcc's on the benq are very flexible!!

As far as I am aware,you can only achieve complete focus,when the triplet and screen are perpendicular to each other.So no,no even focus for me,however,this is 100% not noticeable when watching a movie,subtitles etc look clear as a bell!
So I shall be making a slightly slanted screen,maybe 5 degrees,the rest by keystone,no probs!!

SonicWonder2000

Jun 27 2005, 03:20 PM

QUOTE

Pun, I don't think that tilt alone will create a shift in the position of the projected image, or keystone correct.

Sorry, you are, of course, correct!

I somehow missed the part where you are going to be tilting your mirror along with the triplet... I guess I was thinking about a standard design like mine where there isn't a mirror.

pun15her

Jun 27 2005, 04:17 PM

QUOTE (Haas_man @ Jun 27 2005, 11:09 AM)

I was looking into a pivot on the mirror for my next box, whenever that happens. I have a simular design sketched up. The problem is that the mirror and obj lens need to move at different rates. If the mirror is tipped back 10 deg. , then the obj needs to be be raised by 20 degrees. I have sketched up a design that will compensate for the correction, but it's on paper not CAD. My design also corrects for the keystone angle too. I guess I'm not going to supprise anyone now!

edit: I see that your mirror and lens were not connected. I was trying to do it in one motion. tip the lens up and the mirror and f fres make the correction with simple levers.

Thanks Haas,That lever mech idea,is the perfect way of doing it!!!

Good thinking!

pun15her

Jun 27 2005, 04:18 PM

QUOTE (SonicWonder2000 @ Jun 27 2005, 03:20 PM)

QUOTE

Pun, I don't think that tilt alone will create a shift in the position of the projected image, or keystone correct.

Sorry, you are, of course, correct!

I somehow missed the part where you are going to be tilting your mirror along with the triplet... I guess I was thinking about a standard design like mine where there isn't a mirror.

No sweat,SW!I presumed you had misseed the (crap)diagram!!

pun15her

Jun 28 2005, 12:45 PM

Ok,looks complicated,but I think something like this.....

...might work.It would need to be pretty much slop free,maybe using ballraces,at all the moving joints??
Looking at it, it resembles a cantilever suspension setup!

Haas_man

Jun 28 2005, 02:11 PM

Yes, thats where I was going with my design. Now, add a link hanging from the bottom to adjust the front fres for keystone adj. at 1/1 with the obj carrier. I like the addition of the screw, That didn't cross my mind.

I wanted to curve the top of the front back and mount a piece of thin panel to the obj carrier and drag it up and down to cover the hole. They would overlap on the top and bottom. Focus isn't a problem using the tubular focus tube.

pun15her

Jun 28 2005, 02:49 PM

Like the keystone adjustment idea,Haas.
I know what you mean about the overlapping cover idea,but I thought about doing something low profile and sexy!!!!!!
Maybe something like the half exposed the rear lights of an enzo????

It would take a bit of work,but I think it is do-able,and would look very groovy!!

samuraijack

Jun 29 2005, 01:26 AM

Pun15her,
Normally, I would not do this, but the Fifi reference just couldnt rest...
In Memory of Fifi...

Thought you might get a kick out of this...

SJ

hardflip

Jun 29 2005, 01:18 PM

QUOTE (samuraijack @ Jun 29 2005, 02:26 AM)

Pun15her,
Normally, I would not do this, but the Fifi reference just couldnt rest...
In Memory of Fifi...

Thought you might get a kick out of this...

SJ

Ha ha ha.

I love that kid. I must go find the light sabre version now.

EDIT: Wow the attack of the clones version is most impressive.

Punisher, are you planning on turning your stealth box into a Ferrari now or thinking of version 2?

pun15her

Jun 29 2005, 03:10 PM

Hi,hardflip,howa it going??
Definateley ver2,but its a long way off!!!

Samurai,All I keep getting is a web hosting service page come up!!

Cheers though

samuraijack

Jun 29 2005, 03:15 PM

QUOTE (pun15her @ Jun 29 2005, 03:10 PM)

Hi,hardflip,howa it going??
Definateley ver2,but its a long way off!!!

Samurai,All I keep getting is a web hosting service page come up!!

Cheers though

You can try it now. Its just a page with the link to the video. Looks like another netleech has sold out to advertising though...

pun15her

Jun 29 2005, 03:27 PM

Still couldnt get it,but searched around,and found it here:
Star wars kid as the punisher
Excellent stuff,I love the "bulk" one too!!!

samuraijack

Jun 29 2005, 04:19 PM

QUOTE (pun15her @ Jun 29 2005, 03:27 PM)

Still couldnt get it,but searched around,and found it here:
Star wars kid as the punisher
Excellent stuff,I love the "bulk" one too!!!

Try the Matrix ...

Sorry about that link, it comes through just great on my system. I always test links when I post them. I bet that Ad had something to do with it...

SJ

pun15her

Jun 29 2005, 04:52 PM

QUOTE (samuraijack @ Jun 29 2005, 04:19 PM)

QUOTE (pun15her @ Jun 29 2005, 03:27 PM)

Still couldnt get it,but searched around,and found it here:
Star wars kid as the punisher
Excellent stuff,I love the "bulk" one too!!!

Try the Matrix ...

Sorry about that link, it comes through just great on my system. I always test links when I post them. I bet that Ad had something to do with it...

SJ

He he ,very good,thanks again,Samurai!

jasonx

Jun 29 2005, 07:19 PM

while looking for these videos on screamingpickle did you come across the firewheel
advert looks fun

pun15her

Jun 29 2005, 11:38 PM

QUOTE (jasonx @ Jun 29 2005, 07:19 PM)

while looking for these videos on screamingpickle did you come across the firewheel
advert looks fun

He,that looks pretty fun,unless you have one of these...

Full auto CO2 powered 6mm plastic bb firing SOB.I added the trigger guard unit that has a laser sight and led torch,chopped about 2" ffrom the front end and made a few other cosmetic modifications.Fires 50 bb's in less than 2 secs.I have the bruises to prove it!!!!!!!

neda

Jun 30 2005, 02:03 AM

QUOTE (pun15her @ Jun 29 2005, 07:38 PM)

QUOTE (jasonx @ Jun 29 2005, 07:19 PM)

while looking for these videos on screamingpickle did you come across the firewheel
advert looks fun

He,that looks pretty fun,unless you have one of these...

Full auto CO2 powered 6mm plastic bb firing SOB.I added the trigger guard unit that has a laser sight and led torch,chopped about 2" ffrom the front end and made a few other cosmetic modifications.Fires 50 bb's in less than 2 secs.I have the bruises to prove it!!!!!!!

That looks mean and dangerous, no wonder you are the Punisher....

Mountainbiker54

Jun 30 2005, 02:56 AM

Yay for Airsoft!

got any others?

pun15her

Jun 30 2005, 04:15 PM

QUOTE (Mountainbiker54 @ Jun 30 2005, 02:56 AM)

Yay for Airsoft!

got any others?

My son has a 1:1 scale spas shotgun which is really cool!!,plus 4 spring pistols of varying quality.We are thinking of joining a local air rifle shooting club,and going into target shooting!!!!

Mountainbiker54

Jun 30 2005, 05:08 PM

Mmmm cool!

I have a Glock, and a MP5J and my friend has that MAC 11, Spas 12, and about 10 others :-p

pun15her

Jun 30 2005, 05:22 PM

QUOTE (Mountainbiker54 @ Jun 30 2005, 05:08 PM)

Mmmm cool!

I have a Glock, and a MP5J and my friend has that MAC 11, Spas 12, and about 10 others :-p

I have seen some really nice glocks.
Definateley want one!

Mountainbiker54

Jun 30 2005, 06:22 PM

This is the one I got, its an amazing gun, totaly worth the money!

http://www.shortyusa.com/cart/viewitem.htm...NL=&CA=2&kiosk=

pun15her

Jun 30 2005, 06:52 PM

Very nice,there is a cool site in the UK,here it is,lots of glocks,and check out the MINIGUN!!!!!!!!!!!!!!!!

Wolf armouries
(they also made the guns for AvP,and sell kits to make them!!

pun15her

Jun 30 2005, 08:04 PM

Right!!!
Just to make up for a load of non-pj related stuff,here are a couple of pics from one of my favourates,Princess Mononoke.

Very cool film,that looks incredible on the big one!

Dweezilkid

Jun 30 2005, 09:27 PM

Awesome shots!

And drat! Another great movie somebody else posted pics of before I could